TOOLS

CROSS LOCK TWEEZERS - STRAIGHT TIP

Cross lock tweezers are excellent for applying adjustment corks and felts as well as for general ...

Cross lock tweezers are excellent for applying adjustment corks and felts as well as for general shop use.Made from stainless steel with heat resistant fiber grips. Normal position is closed - squeeze to open.Approximate Length: 6.5" (16.5 cm)Tip Style: straight

FLUTE LEAK ISOLATOR

This simple tool can be very helpful in locating leaks from gaps between tone holes and pads, as ...

This simple tool can be very helpful in locating leaks from gaps between tone holes and pads, as well as key to key adjustments. In addition, this tool will assist in finding broken and porous skins, small holes in pad skins, leaks around pad screws and washers, and to check the integrity of joint sockets and receivers.The Flute Leak Isolator can be used by itself or with the Mag Machine (note that Mag Machine is sold separately).Easy to use, just insert the isolator into the flute body tube ...

RIVET-EZE

Our Rivet-Eze offers real help for installing rivets with a steel backupwasher when doing case re...

Our Rivet-Eze offers real help for installing rivets with a steel backupwasher when doing case repair. Each end has a recessed hole for holding either astandard sized backup washer - 3/8" diameter, or an oversize washer -1/2" diameter. Embedded opposite each recess is a high strength magnet tohold the washer in place. Simply place the washer in the Rivet-Eze recessed areaand insert the tool down between the case lining and the case shell, insert andset the rivet.The slim design, only 1/8" thi...

FLUTE PAD ADJUSTING TOOL

Made from highly polished tool steel, our flute pad adjusting tool works great for pad leveling a...

Made from highly polished tool steel, our flute pad adjusting tool works great for pad leveling and adjustment on both open and closed hole flute pads.Thickness: 0.024" (0.60mm)Overall Length: 3.3" (84mm)

VALENTINO BRASS MOUTHPIECE SHANK TOOL

Use for straightening all brass instrument mouthpiece shanks.On badly dented shanks we recommend ...

Use for straightening all brass instrument mouthpiece shanks.On badly dented shanks we recommend inserting tool into shank and using rawhide mallet to tap the shankback into round.

WIHA PHILLIPS SCREWDRIVER #1 x 60mm

SPECIFICATIONS: tip size: #1 large blade length: 2.3" (60mm) overall length: 6.7" (170mm) ...

SPECIFICATIONS: tip size: #1 large blade length: 2.3" (60mm) overall length: 6.7" (170mm) RECOMMENDED USE: screw type: key guard, valve, and miscellaneous screws instrument: Saxophone, brass valve sections, and general shop use Votaw Tool Company is pleased to offer the Wiha? line of screw drivers. Blades are made of high alloy vanadium-molybdenum steel specially developed for Wiha? and are salt-bath hardened and tempered to provide optimum hardness, maximum torque transfer a...

JEWELER'S SAW

Our excellent quality jeweler's saws are made inGermany to exacting specifications.Features inclu...

Our excellent quality jeweler's saws are made inGermany to exacting specifications.Features include: heavy duty metal frame with comfort grip hardwood handle unique blade tensioning end screw 3" (76mm) frame depth adjusts to hold any plain end blade lengths between 2.5" and 6" (63mm to 152mm) lifetime guarantee

THREAD REDUCER 1/2-13 FEMALE 3/8-16 MALE

ABOUT OURThread Reducers Our Thread Reducers aredesigned to allow the use of dent balls...

ABOUT OURThread Reducers Our Thread Reducers aredesigned to allow the use of dent balls with a thread size that is differentthan the dent rod thread size. Machined from 12L14 steel with case hardenedthreads. Flats have been machined into reducer's sides to accommodate a wrenchfor tightening reducer onto dent rod.The thread sizes listed indicate each reducers actual thread configuration. Forexample, if your dent rod has 1/2-13 threads and you want to attach a dent ballwith 3/8-16 thr...

TAP & DIE ASSORTMENT - ALL METRIC SIZES

Assortment of 9 taps and 9 dies includes one each of thefollowing sizes: 1.7 x 0.35 2.5 x 0.4...

Assortment of 9 taps and 9 dies includes one each of thefollowing sizes: 1.7 x 0.35 2.5 x 0.45 3.5 x 0.60 2.0 x 0.40 3.0 x 0.50 4.0 x 0.70 2.3 x 0.40 3.0 x 0.60 4.0 x 0.75 * General Purpose Plug Taps andAdjustable Dies* High Carbon Steel* Metric Sizes* Die Outside Diameter: 13/16" (20.6mm)

FLAT HEAD BRASS HAMMER

Our #2121 Brass Hammer isdesigned for medium duty general purpose shop use. Head is machined from...

Our #2121 Brass Hammer isdesigned for medium duty general purpose shop use. Head is machined from half hard brass and fitted to a non-corrosive stainless steel shaft fitted with a nicely profiled Delrin handle.HammerDimensions:overall weight: 7 ounces (200g)overall length: 11" (2.8cm)head length: 1.375" (35mm)head diameter: 0.75" (19.05mm)

TROMBONE LEVELING BLOCK

Designed for aligning both inner and outer slidepipes, our #2076 Leveling Block is constructed us...

Designed for aligning both inner and outer slidepipes, our #2076 Leveling Block is constructed using heavy plate glass enclosedin a wood case. Two steel riser blocks machined perfectly flat set on either endof the glass. Slide pipes are set on the riser blocks to determine skew ortwist. Works great for soldering and reassemby work. Whensoldering, simply position the area receiving the heat off of either end of theblock. To help hold pipes in place when soldering order our #2078 TROMBONE SLID...

DENT ROD CLAMP - 1/2" (12.7mm)

Our Dent Rod Clamps work great for holding dent rods, knuckle tools, or mandrels securely in a st...

Our Dent Rod Clamps work great for holding dent rods, knuckle tools, or mandrels securely in a standard bench vise. Locks rod in tight to prevent slippage and also protects rods from being marred by vise jaws.The two halves of the clamp are secured together to allow easy clamping and positioning in the vise. Slides on and off rod so it can be quickly interchanged with other rods. Works for all 1/2" (12.7mm) diameter rods or mandrels.

DENT ROD CLAMP - 3/8" (9.5mm)

Our Dent Rod Clamps work great for holding dent rods, knuckle tools, or mandrels securely in a st...

Our Dent Rod Clamps work great for holding dent rods, knuckle tools, or mandrels securely in a standard bench vise. Locks rod in tight to prevent slippage and also protects rods from being marred by vise jaws.The two halves of the clamp are secured together to allow easy clamping and positioning in the vise. Slides on and off rod so it can be quickly interchanged with other rods. Works for all 3/8" (9.5mm) diameter rods or mandrels. Other sizes available - see below.